Behringer Minimon Mon800 Schnellstart Anleitung PDF herunterladen (Seite 5)

(1) (2)

(3) (8) (11) (12) (13)(6)

(4) (7) (9) (10)(5)

(14) (17)(16)

(15)

(18) (19) (20) (21) (22)

MINIMON MON800

Controls

(EN) Controls

(10) Use the TALK LEVEL control

to adjust the sensitivity of the

talk-backmicrophone.

(11) The talk-back microphone is

installed behind the MIC openings.

Speakinto the microphone to

make announcements which

are then routed to the recording

devices connected to the

2-TRACK OUT outputs.

(12) The TALK TO CUE/PHONES/SPK

A and TALK TO 2-TR OUT buttons

determine where the talk-back

microphone signal is routed to (9).

(13) The switch turns your MINIMON

MON800 on and o.

(14) The MON800 is connected to the

mains using a 2-pole POWER

connector jack. A matching mains

adaptor is included with the unit.

(15) A second pair of headphones

can be connected to the PH jack.

This connector is wired in parallel

with the front-panel jack (3).

(16) The TB jack is used to connect a single

footswitch (12).

(17) Two pairs of loudspeakers can be

connected to the SPEAKERS OUT B

and C jacks.

(18) Connect your main monitor speakers

to the SPEAKERS OUT A jack.

(19) CUE OUT is an additional output,

which you can use to route

the MINIMON signals to other

devices, such as an additional

headphones amp.

(20) The two 2-TRACK OUT jacks are

wired in parallel and carry the

same signals. Use the ¼" or cinch

outputs, depending on the recording

device used.

(21) Use the CD/TAPE IN jacks C and D to

connect playback devices, such as a

computer, CD/MD or cassette player.

(22) The MIX IN jacks A and B are for

connecting the main signal sources

(e.g.mixing console, audio card, etc.)

using ¼" plugs. Mono signals must be

connected to the L jacks.

(1) Use the four switches in the SOURCE

section to select up to four input

sources (MIX A and B, CD/TAPE C and D)

for monitoring and recording.

(2) The two LED displays are for

monitoring the output level of the

2-TRACK OUT outputs. They comprise

6 LEDs each. When the CLIP LED lights

up, thisindicates that distortion

may occur.

(3) A pair of headphones with a ¼" TRS

connector (e.g. BEHRINGER HPS5000)

can be connected to the PHONES jack.

This output is wired in parallel with the

rear-panel output jack (15), so that up

to two headphones can be used at the

same time.

(4) With the PHONES LEVEL control you

can adjust the volume for the two

headphones jacks on the front or rear

panel respectively.

(5) SPK A LEVEL governs the volume

level of the SPEAKERS OUT A outputs

(18). SPK B + C LEVEL allows you to

set the volume for outputs B and C

(17) simultaneously.

(6) Use the switches A/B/C ON to switch

the speakers A, B and C on and o.

(7) With the MUTE switch you can

disable all loudspeaker and

headphonesoutputs.

(8) The MONO switch switches all monitor

paths to mono.

(9) The DIM switch lowers the level of the

monitor paths by -20 dB. This allows

you, for example, to talk to somebody

while mixing without losing track of

the recording.

8 MINIMON MON800 9 Quick Start Guide

Check Out behringer.com for

Full Manual

1 2 3 4 5 6 7 8 9 10 11 12 13

Kommentare zu diesen Handbüchern

Keine Kommentare